• +91-85699-09696

Conveyor System Trainer Manufacturer,Supplier and Exporter in India

Conveyor System Trainer

Product Code : JA-DAIAPC-9613

The Conveyor System Trainer teaches control with programmable logic controllers through a common industrial task: sorting items as they travel along a conveyor. It was designed around the needs of PLC control teaching. Students wire it, program it and watch each part reach its proper place.

Specifications of the Conveyor System Trainer

Product codeJA-DAIAPC-9613
ApplicationSorting items as they travel along a conveyor, under PLC control
ConveyorBench belt conveyor driven by a geared DC motor at 24 V DC
Part sensorsInductive proximity sensor to tell metal from non-metal parts; optical sensors for part presence; colour sensor for sorting by colour
Sorting actuatorsPneumatic cylinders with solenoid valves, or electric pushers, that push parts off the belt; pneumatic versions need a compressed air supply
Sorting stationsThree chutes or bins for the sorted parts
PLC connection24 V DC inputs and outputs brought out to sockets, terminals or a multi-pin connector, for wiring to a PLC trainer
I/O needed on the PLCAbout 7 to 14 digital inputs and 5 to 6 digital outputs
Typical exercisesBelt start-stop, part detection, pusher actuation, sorting metal from non-metal parts and sorting by colour
Supplied byJaincoLab

Sorting exercises on the Conveyor System Trainer

  • Belt and sensors first. Connect the conveyor to the Programmable Logic Controller Trainer. Start and stop the belt from push-buttons and check that each sensor input lights as a part passes it.
  • Metal or plastic. Feed a mix of metal and plastic parts along the belt. Use the inductive sensor signal to decide which pusher fires, and count the parts that reach each chute.
  • Pneumatic pushers. Before running the air-driven pushers, practise cylinder and solenoid valve circuits on the Electro Pneumatic Trainer. Take the air from an Air Compressor through a regulator.

Frequently Asked Questions

Which sensor on a sorting conveyor tells metal parts from plastic ones?
An inductive proximity sensor switches only when metal comes close, so it ignores plastic parts. An optical sensor sees every part. Used together, the optical sensor says a part is present and the inductive sensor says whether it is metal.

Why can an optical sensor miss shiny or clear parts on the belt?
A diffuse optical sensor needs light reflected back to it. A shiny part can throw the light away at an angle, and a clear part lets it pass straight through. Tilting the sensor, adjusting its sensitivity or using a through-beam light barrier usually cures the problem.

How does the PLC know when a part has reached the ejector?
Either a second sensor sits just before the ejector, or the PLC tracks the part from the entry sensor. With tracking, a timer set to the belt travel time, or a shift register stepped by belt pulses, fires the pusher when the part arrives. Tracking lets several parts sit on the belt at once.

What should be checked on the air supply before students run the pneumatic pushers?
Set the regulator to the pressure given in the manual and drain any water from the filter. Check that the safety valve works and that the main shut-off is easy to reach. Make sure the hoses are pushed fully home, and keep fingers clear of the cylinders while the belt runs.

What sensor types should our tender name for a PLC sorting conveyor?
Name an inductive proximity sensor for metal parts, optical sensors for part presence and a colour sensor if parts are sorted by colour. State the PLC interface too, such as 24 V DC I/O on sockets. JaincoLab can build the trainer to your own specification; send it through our tenders page.

Can the conveyor trainer be wired to a PLC we already have in the lab?
Usually, yes. Its sensors and actuators work on 24 V DC signals brought out to sockets or terminals. Give the make of your PLC and say whether its inputs are sinking or sourcing. Send this through our contact page, so the wiring can be matched.

Other PLC equipment in the range

For Ministry of Education, World Bank and United Nations laboratory projects, JaincoLab works as manufacturer and exporter and has completed such supplies successfully in many countries. Firms preparing bids for these tenders can request itemised quotations and turnkey supply of the full laboratory scope from our tenders team.

See the Data Acquisition, Instrumentation and Process Control range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.

For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.

Last updated: 16 November 2026

   

Office Address

Jain Scientific Suppliers
2475-84, Hargolal Road,
Ambala Cantt, Haryana, India

[email protected]

+91-85699-09696

Follow Us